-
- Out of Stock
- Other Modules
CH376S U Disk Read Write Module For USB Control Transfer
- 110.00 EGP
- CH376 is common a USB bus interface chip, with 8 bit data bus and reading, writing and chip select lines and interrupt output, can easily attached to the system bus of the single chip microcomputer /DSP/MCU/MPU controller.
- Read more
-
-
- Other Modules
Relay Module 1 Channel 5V
- 40.00 EGP
- The Single Channel Relay Module is a convenient board that can be used to control high voltage, high current loads such as motor, solenoid valves, lamps, and AC load. It is designed to interface with microcontrollers such as Arduino, PIC and etc. The relays terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes…
- Add to cart
-
- Other Modules
I2C Arduino Serial Module For LCD 16*2
- 55.00 EGP
- This is I2C Arduino Serial Module For LCD board that can be connected to a standard HD44780 compatible 16×2 , 20×4 or 20×2 Character Display Module that supports 4 bit mode.This board has a PCF8574 I2C chip that converts I2C serial data to parallell data for the LCD display.
- Add to cart
-
- Other Modules
Joystick Module X-Y For Arduino
- 40.00 EGP
- Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
- Add to cart
-
- Modules, Other Modules
Mini 5V Traffic Light LED Display Module for Arduino Red Yellow Green 5mm LED
- 40.00 EGP
- Mini 5V Traffic Light LED Display Module for Arduino Red Yellow Green 5mm LED RGB -Traffic Light for Traffic Light System Model
- Add to cart
-
- Other Modules
Micro-USB Female Breakout Module
- 15.00 EGP
- A Female MicroUSB port with breakout board so you can solder on wires or header pins and integrate into any project.
- Add to cart
-
- Other Modules
GY-521 MPU6050 Triple 3-Axis Accelerometer Gyroscope I2C
- 155.00 EGP
- The MPU6050 contains both a 3-Axis Gyroscope and a 3-Axis accelerometer allowing measurements of both independently, but all based around the same axes, thus eliminating the problems of cross-axis errors when using separate devices.
- Add to cart
-
- Other Modules
MAX6675 Module for Thermocouple K Type
- 240.00 EGP
- This K Type Thermocouple can be used to measure temperatures up to 600 degree Celsius! Great for industrial projects, 3D Printers, DIY and hobby projects which require a high temperature to be measured.
- Add to cart
-
- Other Modules
Relay Module 4 Channel – 5V DC
- 140.00 EGP
- Relay Module 5Vdc – 4 Relay For Arduino & MCU H/L Trigger
- Add to cart
-
- Components, Other Modules, Relays
Relay Module 2 Channel 12V (high/low) level trigger
- 75.00 EGP
- This is a HIGH/LOW Level 12V 2-channel relay interface board, and each channel needs a 20mA driver current. It can be used to control various appliances and equipment with large current. It is equipped with high-current relays that work under AC 250V 10A or DC 30V 10A. It has a standard interface that can be controlled directly by microcontroller
- Add to cart
-
- Out of Stock
- Other Modules
12V Delay Timer Switch Adjustable
- 45.00 EGP
- This 12V Delay Timer Switch Adjustable 0-10sec is one kind of popular switch module. You can use it control any devices on or off. This is a DC12V controlled 1 channel timer relay module. It has a NE555 timer chip on the board. You can adjust delay time(0-10s) by rotating the potentiometer. When this relay get powered it will delay…
- Read more
-
-
- Out of Stock
- Other Modules
1.2v 12v ZB2L3 18650 Li-ion Lithium Battery Capacity Tester + Resistance Lead-acid Battery Capacity Meter Discharge Tester
- 140.00 EGP
- This circuit in order to improve the voltage measurement accuracy, specially designed DC bias, when the terminal is what all don't pick will display a small voltage, does not affect the actual measurement, if you are short connected with the input terminal (absolute 0V) will display 0. To understand the principle can consult the superposition theorem in electrical engineering.
- Read more
-
-
- Other Modules
Micro SD Card Module
- 40.00 EGP
- Micro SD card mini TF card reader module SPI interfaces with level converter chip
- Add to cart
-
- Other Modules
Relay Module 2 Channel 5V (high/low) level trigger
- 80.00 EGP
- Relay Module 2 Channel 5V is a LOW Level 5V 2-channel relay interface board, and each channel needs a 20mA driver current. It can be used to control various appliances and equipment with large current. It is equipped with high-current relays that work under AC 250 V -10 A or DC 30 V 10 A. It has a standard interface that…
- Add to cart
-
- Other Modules
NE555 Adjustable Frequency Pulse Generator Module
- 20.00 EGP
- This is a square wave pulse generator module based on the ubiquitous NE555 timer IC. The module can be powered from a wide power supply range (5 to 12V) and will produce a continuous square wave output between 4Hz to 1.3KHz which can be set by on on-board multi-turn potentiometer. Module has ten-turn frequency adjustment control and power on LED.…
- Add to cart
-
- Other Modules
Single Channel 5V DC Relay Module Solid State Low Level Trigger
- 70.00 EGP
- Single Channel 5V DC Relay Module Solid-State Low-Level Trigger, output with resistive fuse (240V 2A) It is a 1-channel solid state relay board, which can be controlled by a wide range of microcontrollers such as AVR, PIC, ARM, PLC, etc. With blue KF301terminal, more convenient for control line Standard interface can be connected with microcontrollers Solid State Relay Module Product…
- Add to cart
-
- Out of Stock
- Other Modules
12V Battery Level LED Indicator
- 45.00 EGP
- XD-82B 12V Battery Level Indicator Module 4 Paragraph 4 onboard Battery Indicator LED Lights. Monitor the level of your 12v battery and know when it’s running low with this small LED battery level indicator.
- Read more
-
-
- Batteries & Accessories, Modules, Other Modules
LCD Dual USB 5V 1A 2.1A Mobile Power Bank Module
- 160.00 EGP
- LCD Dual USB 5V Power Bank Charger Module with LCD & Dual USB interface 5V 1A 2.1A With Automatic Protection
- Add to cart
-
- Other Modules
2 Channel 5V DC Relay Module Solid State Low Level trigger
- 185.00 EGP
- 5V solid state relay 240V 2A, output with resistive fuse 240V 2A
- Add to cart
-
- Out of Stock
- Modules, Other Modules
Rgb Led Module
- 10.00 EGP
- RGB LED is a light emitting diode that displays just about any color by manipulating the intensities of either the Red, the Green or the Blue LED.
- Read more
-
-
- Out of Stock
- Other Modules
Lipo Battery Voltage Tester / Low Voltage Buzzer Alarm
- 55.00 EGP
- LIPO Battery Voltage Tester and low voltage buzzer alarm combo is easy to use. Li-Po Battery Voltage Buzzer Indicator: directly plug it into your operating battery, it will monitor the conditions of your battery all the time, so your batteries shall remain within safe operating voltage range at all times.
- Read more
-
-
- Out of Stock
- Batteries & Accessories, Chargers, Lithium Batteries, Modules, Other Modules
Lithium Battery Charger Protection Module (BMS) 5S 15A 21V
- 100.00 EGP
- 5S 15A Li-ion Lithium Battery 18650 Charger PCB BMS 18.5V 21V Cell Protection Board Integrated Circuits
- Read more
-
-
- Other Modules
Led Matrix 8×8 With MAX7219 Module
- 140.00 EGP
- The MAX7219 Dot Led Matrix Module is a serial input common-cathode driver that interfaces micro-controllers to LED matrices
- Add to cart
-
- Other Modules
3D Printer Optical End Stop Switch Module
- 35.00 EGP
- 3D Printer Optical End Stop Switch Module Key Features and Enhancements: High-Quality Cable: The module comes with a 22AWG cable line featuring thick copper wire. This high-quality cable ensures stable and reliable connections. Secure Connection: The cable line is designed to be securely attached, making it resistant to accidental disconnection during operation. This feature enhances the overall safety and reliability…
- Add to cart
-
- Out of Stock
- Other Modules
IRF520 MOSFET Driver Module
- 27.50 EGP
- IRF520 MOSFET Driver Module
- Read more
-
-
- Other Modules
Ublox NEO-6m GPS tested Module v2
- 425.00 EGP
- Ublox makes good gps. The Ublox NEO-6M gps engine on this board is a quite good one, with high precision binary output. It has also high sensitivity for indoor applications. The gps module have a battery for power backup and EEprom for storing configuration settings. The antenna is connected to module through ufl cable which allow for flexibility in mounting…
- Add to cart
-
- Out of Stock
- Ethernet, Modules, Other Modules, Wireless
A9G Development Board Module (GPS GSM GPRS)
- 1,200.00 EGP
- ORIGINAL AI-THINKER A9G GSM/GPRS GPS/BDS DEVELOPMENT BOARD SMS VOICE WIRELESS DATA TRANSMISSION POSITIONING
- Read more
-
-
- Other Modules
GY-273 3-Axis Compass Magnetometer Sensor Module
- 250.00 EGP
- GY-273 DC 3V-5V HMC5883L Triple Axis Compass Magnetometer Sensor Module Three Axis Magnetic Field Module for Arduino
- Add to cart
-
- Other Modules
High-power MOSFET Trigger Switch Drive Module
- 40.00 EGP
- High-power MOSFET Trigger Switch Drive Module
- Add to cart
-
- Other Modules
GY-271 HMC5883L Compass
- 100.00 EGP
- GY-271 HMC5883L 3-Axis Magnetic Electronic Compass Module is designed for low-field magnetic sensing with a digital interface and it is perfect to give precise heading information. This compact sensor fits into small projects such as UAVs and robot navigation systems. The sensor converts any magnetic field to a differential voltage output on 3 axes. This voltage shift is the raw digital…
- Add to cart
-
- Modules, Other Modules
LASER Receiver Module
- 40.00 EGP
- The laser receiver sensor module uses a non-modulated laser receiver to detect the laser signal.
- Add to cart
-
- Other Modules
MCP2515 CAN Bus Module Board TJA1050 Receiver SPI For 51 MCU
- 230.00 EGP
- The MCP2515 Module adopts CAN controller MCP2515, and TJA1050 high-speed CAN transceiver. Microchip MCP2515 independent CAN protocol controller, support CAN V2.0B regulation. The connection between MCP2515 and MCU is through SPI.
- Add to cart
-
- Out of Stock
- Other Modules
Relay Module 16 Channel 5V
- 231.00 EGP
- Relay Module 16 Channel 5V
- Read more
-
-
- Out of Stock
- Modules, Other Modules, Switches
Tilt Switch Module KY020
- 35.00 EGP
- Module
- Read more
-
-
- Modules, Other Modules
4 Channel 5V Relay Module Board Shield for Arduino
- 275.00 EGP
- 4 Channel 5V Relay Module Board Shield for Arduino This 5V 4 Relay Shield Module is a small current signal control power equipment commonly used electronic module Enabling high-power single-chip control devices are widely used in SCM system to make smart home project Can be directly plugged into the compatible the use of various types of motherboards, eliminating the patch…
- Add to cart
-
- Other Modules
3 Axis Digital Gyroscope Sensor Module GY-50 L3G4200
- 125.00 EGP
- The L3G4200D has a full scale of /-250 / /-500 / /-2000 dps and is capable of measuring rates with a user-selectable bandwidth.These work great in gaming and virtual reality input devices, GPS navigation systems and robotics.With the given Arduino library, you can easliy setup your project as you get this product.
- Add to cart
-
- Other Modules
1.75mm Filament Detection Sensor Module
- 110.00 EGP
- 1.75mm Filament Detection Sensor Module
- Add to cart
-
- Other Modules
GY-45 MMA845 3-Axis Accelerometer Module
- 100.00 EGP
- The MMA8452 is a smart low-power, three-axis accelerometer with 12 bits of resolution. This accelerometer is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. The MMA8452 has user selectable full scales of ±2g/±4g/±8g. The device can be configured to generate inertial wake-up interrupt signals allowing the MMA8452 to monitor events and remain in a…
- Add to cart
-
- Other Modules
FMP10 Fingerprint Recognition Module
- 1,250.00 EGP
- FMP10 Fingerprint Recognition Module
- Add to cart
-
- Other Modules
Photosenstive Diode Module
- 27.50 EGP
- Photosenstive diode module is the most sensitive for environmental light intensity, generally used for detecting the ambient brightness and intensity. In most of the cases with photosenstive resistance sensor module universal, it is difference that is the photosensitive diode module directional well and can sense the fixed direction of light source
- Add to cart
-
- Modules, Other Modules
BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module
- 70.00 EGP
- DESCRIPTION Now we’ve got a high-precision environmental sensor at even lower cost, Barometer Sensor(BMP280). It is based on their new BMP280 sensor, which is an upgraded version of the old BMP180 Barometer Sensor (BMP180). The module provides precise measurement of barometric pressure and temperature in the environment. The air pressure can be measured in a range from 300 hPa to…
- Add to cart
-
- Out of Stock
- Other Modules
3D Printer Mechanical End Stop Switch Module
- 35.00 EGP
- 3D Printer Mechanical End Stop Switch Module is a Mechanical End stop kit or 3D Printers or CNC machines.
- Read more
-
-
- Out of Stock
- Other Modules
Kingston Canvas Select Plus 32GB Micro SD Card
- 121.00 EGP
- Read more
-
-
- Out of Stock
- Other Modules
XY-LJ02 Timer Relay Delay Switch Module With LCD
- 137.50 EGP
- XY-LJ02 Timer Relay Delay Switch Module Delay Power Off and Trigger Delay Cycle Timing Circuit Switch with LCD Digital Display Compatible with Arduino
- Read more
-
-
- Out of Stock
- Other Modules
SILICON POWER USB Flash Ultima U03, 32GB, USB 2.0
- 110.00 EGP
- Elegant and stylish USB drive with luxurious diamond cut pattern and 32GB storage capacity
- Read more
-
-
- Out of Stock
- Other Modules
16 Channel Analog Multiplexer
- 38.50 EGP
- Multiplexer Module is a micro chip that requires 1 Analog Pin and 2 to 4 Digital Pins to allow the micro controller to monitor more Analog Pins for sensor readings. The requirement of 1 Analog Pin is actually the output pin shared among all the extension Analog Pins. The module only allow 1 Analog channel or sensor value to be connected to…
- Read more
-
-
- Out of Stock
- Other Modules
MAX6675 Module for Thermocouple K Type
- 110.00 EGP
- Read more
-
-
- Out of Stock
- Other Modules
ADS1115 16-Bit ADC – 4 Channel with Programmable Gain Amplifier
- 95.00 EGP
- For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the…
- Read more
-
-
- Out of Stock
- Other Modules
SD Card Module, SPI Interface
- 55.00 EGP
- This is a wonderful little Arduino to SD card interface module.Through programming, you can read and write to the SD card using your arduino.If you are feeling adventurous, this is truly an interesting board to work with and learn from.It is easily interfaced as a peripheral to your arduino sensor shield module.
- Read more
-
-
- Out of Stock
- Other Modules
Relay Module 8 Channel 5V
- 195.00 EGP
- This is a 5V 8-Channels Relay module, It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and MSP430. 8 relays are included in this module, with “NC” ports means “Normally connected to COM” and “NO” ports means “Normally open to COM”. This module also equipped with 8 LEDS to show the status…
- Read more
-
-
- Out of Stock
- Other Modules
Relay 1 channel 30A 240VAC
- 55.00 EGP
- 30A relay module, normally open interface with maximum load: AC 240V/30A, DC 30V/30A
- Read more
-
-
- Other Modules
Reed Switch Module
- 35.00 EGP
- Reed switch is a kind of passive electronic switching component with contacts with a simple structure, small size and easy to control. It consists of a sealed glass envelope where there are two ferrous elastic reeds and is filled with inert gas called rhodium
- Add to cart
-
- Out of Stock
- Other Modules
GY-88 IMU 10DOF MPU6050 + HMC5883L + BMP085
- 220.00 EGP
- This IMU 10DOF is a motion tracking module. Its design is based on the sensor MPU6050,HMC5883L and BMP085. The sensor MPU6050 which is the world’s first integrated 6-axis Motion Tracking device, that combines a 3-axis gyroscope, 3-axis accelerometer, and a Digital Motion Processor (DMP). The Honeywell’s HMC5883L which is a 3-axis digital compass. The BMP085 is a high-accuracy chip to…
- Read more
-
-
- Out of Stock
- Other Modules
GY-65 BMP085 Atmospheric Pressure Altimeter Module
- 72.00 EGP
- GY-65 BMP085 is a high precision, ultra-low power consumption pressure sensors, can be applied to mobile devices. Its performance, the absolute accuracy of the minimum can reach 0.03hPa, and very low power consumption, only 3A. BMP085 powerful 8-pin ceramic-lead chip carrier (LCC) ultra-thin package, through the I2C bus can be connected directly with a variety of microprocessor.
- Read more
-
-
- Out of Stock
- Other Modules
GY-61 DXL335 3-Axis Accelerometer Module
- 180.00 EGP
- GY-61 ADXL335 Module is a small, thin, low-power, complete 3-axis accelerometer with signal conditioned voltage outputs. The ADXL335 Module 3-axis Analog Output Accelerometer measures acceleration with a minimum full-scale range of ±3 g. It can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion, shock, or vibration. This breakout board comes with…
- Read more
-
-
- Out of Stock
- Other Modules
GY-291 ADXL345 3-Axis Accelerometer
- 60.50 EGP
- GY-291 ADXL345 3-Axis is a small and efficient sensor with a high resolution (13-bit) that can measure an acceleration of up to ± 16g. The module can be accessed via the I2C or SPI protocol and can be supplied with a voltage between 3V and 5V.
- Read more
-
-
- Sale!
- Other Modules
MCR12 Barcode Reader / Scanner Module
- Original price was: 1,500.00 EGP.950.00 EGPCurrent price is: 950.00 EGP.
- Decode nearly any kind of 1D (striped) barcode in your project using this adorable compact barcode scanner. We've looked all over for a small, light, low-power module that can be easily integrated. This OEM scanner has a little camera inside that takes 100 photos per second, instead of using a 'scanning mirror' assembly. This means its less likely to get…
- Add to cart
