-
ESP8266 WiFi 4 channel Relay Module
DC 12V ESP8266 4 channel relay board ESP-01 WIFI module 4 channel WIFI relay module for smart home smart furniture
450.00 EGPESP8266 WiFi 4 channel Relay Module
450.00 EGP -
ESP8266 Wifi Transceiver Module ESP03
ESP8266 Small transceiver module Wi-Fi-based chip, compatible with standard 802.11 b / g / n 2.4 GHz, has SPI interface, 7 GPIO, TCP / IP stack and antenna ceramic PCB.
Ideal for wireless sensor networks, home automation, building automation, and custom applications. Power: 3.3 Vdc, dimensions (mm): 17.4 x 12.2.
66.00 EGPESP8266 Wifi Transceiver Module ESP03
66.00 EGP -
FTDI Module – USB to TTL (Switchable 3.3 or 5V) FT232RL
The FTDI USB to TTL serial converter module is a UART (universal asynchronous receiver-transmitter) board used for TTL serial communication. It is a breakout board for the FTDI FT232R chip with a USB interface, can use 3.3 or 5 V DC and has Tx/Rx and other breakout points.
150.00 EGP -
GY-291 ADXL345 3-Axis Accelerometer
GY-291 ADXL345 3-Axis is a small and efficient sensor with a high resolution (13-bit) that can measure an acceleration of up to ± 16g.
The module can be accessed via the I2C or SPI protocol and can be supplied with a voltage between 3V and 5V.
60.50 EGPGY-291 ADXL345 3-Axis Accelerometer
60.50 EGP -
GY-61 DXL335 3-Axis Accelerometer Module
GY-61 ADXL335 Module is a small, thin, low-power, complete 3-axis accelerometer with signal conditioned voltage outputs.
The ADXL335 Module 3-axis Analog Output Accelerometer measures acceleration with a minimum full-scale range of ±3 g.
It can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion, shock, or vibration.
This breakout board comes with an onboard voltage regulator and works at both 3.3V & 5V (3-5V).
An accelerometer is an electro-mechanical device that will measure acceleration forces.
These forces may be static, like the constant force of gravity pulling at your feet, or they could be dynamic – caused by moving or vibrating the accelerometer.
180.00 EGPGY-61 DXL335 3-Axis Accelerometer Module
180.00 EGP -
GY-65 BMP085 Atmospheric Pressure Altimeter Module
GY-65 BMP085 is a high precision, ultra-low power consumption pressure sensors, can be applied to mobile devices. Its performance, the absolute accuracy of the minimum can reach 0.03hPa, and very low power consumption, only 3A.
BMP085 powerful 8-pin ceramic-lead chip carrier (LCC) ultra-thin package, through the I2C bus can be connected directly with a variety of microprocessor.
72.00 EGP -
HC-06 Bluetooth Module
- The HC-06 is a class-2 slave Bluetooth module.
- It is designed to enable wireless serial communication between microcontroller (like Arduino) and other Bluetooth enabled devices.
- All data received through the serial input is immediately transmitted wirelessly by the module, when the module receives some wireless data from the master device (like a smartphone), this data is sent out through the serial interface.
- A Logic Level Converter is recommended to convert the 5v input to 3.3V.
200.00 EGPHC-06 Bluetooth Module
200.00 EGP -
HC-12 Wirless Transceiver Module (1KM)
Transceiver Module
HC-12 Wireless Transceiver Module (SI4438, 433MHz, 1km)
250.00 EGPHC-12 Wirless Transceiver Module (1KM)
250.00 EGP -
-
Hi Link AC-DC Module 220Vac to 3.3Vdc “HLK-PM03”
Hi Link AC-DC Module 220Vac to 3.3Vdc “HLK-PM03”
-
AC-DC 220V To 3.3Visolating Switch Power Supply Module/ Step-Down Module
-
Output Overload And Short Circuit Protection
-
Low Power Consumption, Environmental Protection, No-Load Loss <0.1W
-
The Product Is Designed to Meet the Requirements of EMC And Safety Test
-
It can use in IOT project, Smart home and so on.
88.00 EGP -
-
HW-183 Board DC-DC Step Up Power Module 2A B6287
HW-183 Board DC-DC Step Up Power Module 2A B6287
- The whole network’s smallest adjustable boost module can be easily installed in a variety of small equipment.
- The module supports Micro USB input, a USB charger or mobile power supply can easily get to it 9V, 12V, 15V, 18V, 24V, easy to use.
32.00 EGP -
IBT-2 Motor Driver 43A
IBT-2 43A H-Bridge Motor Driver Module the drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection.
motor driver H-bridge driver circuit, with strong drive and braking effect, use 74HC244 chip effectively isolate the microcontroller and the motor drive High Current up to 43A
IBT-2 motor driver is a fully integrated high current H bridge module for motor drive applications.
Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with current sense, slew rate adjustment, dead time generation and protection against overtemperature, overvoltage, under voltage, overcurrent and short circuit.
provides a cost optimized solution for protected high current PWM motor drives with very low board space consumption.
The 43a motor driver IBT-2 H-bridge module is an inexpensive, high power motor driver based on two BTS7960 chips
This driver 43a motor driver uses two high current half bridge Infineon BTS 7960 chip for motor drive applications. Interfacing to a microcontroller is made easy using this driver which features current sensing, slew rate adjustment and protection against over temperature, overvoltage, under voltage, over current and short circuit.
This small size driver provides a cost optimized solution for protected high current PWM motor drives.
275.00 EGPIBT-2 Motor Driver 43A
275.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories