-
Inverter Module DC 12V to AC 110V 175V 220V – 150W
150W converter DC 12V TO AC 220V inverter boost module step up board
170.00 EGP -
MAX485 TTL To RS485 Converter Module
5V MAX485 TTL To RS485 Converter Module Board For Arduino
60.00 EGPMAX485 TTL To RS485 Converter Module
60.00 EGP -
Mini MP1584EN DC-DC Buck Adjustable Step Down Module 4.5V-28V Input 0.8V-20V Output
The Mini MP1584 DC-DC 3A Adjustable Buck module is ultra small adjustable 0.8V to 20V output DC to DC Buck converter uses an MP1584EN high frequency switching regulator and integrated high voltage power MOSFET.
30.00 EGP -
I2C Arduino Serial Module For LCD 16*2
This is I2C Arduino Serial Module For LCD board that can be connected to a standard HD44780 compatible 16×2 , 20×4 or 20×2 Character Display Module that supports 4 bit mode.This board has a PCF8574 I2C chip that converts I2C serial data to parallell data for the LCD display.
80.00 EGPI2C Arduino Serial Module For LCD 16*2
80.00 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP -
ESP8266 ESP-12F Wifi Transceiver Wireless Module
The Latest ESP-12F ESP8266 Wi-Fi Module AP & Station Remote Serial Wireless IoT Board is an integrated chip designed for the needs of a new connected world.
It can handle all the necessary overhead for communicating with your network, such as TCP/IP stack and communicating with your 802.11 networks.
It is completely addressable over SPI and UART protocols allowing you to connect your sensors or project directly to it through its GPIO’s. ESP8266 is a low-cost Wi-Fi chip with a full TCP/IP stack and MCU (Micro Controller Unit) capability.
ESP8266 Serial Wi-Fi Wireless Transceiver Module is a self-contained SOC with an integrated TCP/IP protocol stack that can give any microcontroller access to your Wi-Fi network.
ESP8266 Serial Wifi Wireless Transceiver Module is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor.
Each ESP8266 module comes pre-programmed with an AT command set firmware, meaning, you can simply hook this up to your Arduino device and get about as much Wi-Fi-ability as a Wi-Fi Shield offers.
The ESP8266 module is an extremely cost-effective board with a huge, and ever-growing, community.
ESP8266 Serial Wi-Fi Wireless Transceiver Module has a powerful enough onboard processing and storage capability that allows it to be integrated with the sensors and other application-specific devices through its GPIOs with minimal development up-front and minimal loading during runtime.
Its high degree of on-chip integration allows for minimal external circuitry, including the front-end module, which is designed to occupy a minimal PCB area.
The ESP8266 supports APSD for VoIP applications and Bluetooth co-existence interfaces, it contains a self-calibrated RF allowing it to work under all operating conditions and requires no external RF parts.
185.00 EGP -
FTDI Module – USB to TTL (Switchable 3.3 or 5V) FT232RL
The FTDI USB to TTL serial converter module is a UART (universal asynchronous receiver-transmitter) board used for TTL serial communication. It is a breakout board for the FTDI FT232R chip with a USB interface, can use 3.3 or 5 V DC and has Tx/Rx and other breakout points.
150.00 EGP -
Mini 5V Traffic Light LED Display Module for Arduino Red Yellow Green 5mm LED
Mini 5V Traffic Light LED Display Module for Arduino Red Yellow Green 5mm LED RGB -Traffic Light for Traffic Light System Model
30.00 EGP -
Micro-USB Female Breakout Module
A Female MicroUSB port with breakout board so you can solder on wires or header pins and integrate into any project.
15.00 EGPMicro-USB Female Breakout Module
15.00 EGP -
GY-521 MPU6050 Triple 3-Axis Accelerometer Gyroscope I2C
The MPU6050 contains both a 3-Axis Gyroscope and a 3-Axis accelerometer allowing measurements of both independently, but all based around the same axes, thus eliminating the problems of cross-axis errors when using separate devices.
150.00 EGP -
MAX6675 Module for Thermocouple K Type
This K Type Thermocouple can be used to measure temperatures up to 600 degree Celsius! Great for industrial projects, 3D Printers, DIY and hobby projects which require a high temperature to be measured.
285.00 EGPMAX6675 Module for Thermocouple K Type
285.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories