-
GY-291 ADXL345 3-Axis Accelerometer
GY-291 ADXL345 3-Axis is a small and efficient sensor with a high resolution (13-bit) that can measure an acceleration of up to ± 16g.
The module can be accessed via the I2C or SPI protocol and can be supplied with a voltage between 3V and 5V.
60.50 EGPGY-291 ADXL345 3-Axis Accelerometer
60.50 EGP -
LASER Receiver Module
The laser receiver sensor module uses a non-modulated laser receiver to detect the laser signal.
55.00 EGPLASER Receiver Module
55.00 EGP -
Lipo Battery Voltage Tester / Low Voltage Buzzer Alarm
LIPO Battery Voltage Tester and low voltage buzzer alarm combo is easy to use.
Li-Po Battery Voltage Buzzer+Indicator: directly plug it into your operating battery, it will monitor the conditions of your battery all the time, so your batteries shall remain within safe operating voltage range at all times.
55.00 EGP -
SD Card Module, SPI Interface
This is a wonderful little Arduino to SD card interface module.Through programming, you can read and write to the SD card using your arduino.If you are feeling adventurous, this is truly an interesting board to work with and learn from.It is easily interfaced as a peripheral to your arduino sensor shield module.
55.00 EGPSD Card Module, SPI Interface
55.00 EGP -
Relay 1 channel 30A 240VAC
30A relay module, normally open interface with maximum load: AC 240V/30A, DC 30V/30A
55.00 EGPRelay 1 channel 30A 240VAC
55.00 EGP -
Micro SD Card Module
Micro SD card mini TF card reader module SPI interfaces with level converter chip
50.00 EGPMicro SD Card Module
50.00 EGP -
High-power MOSFET Trigger Switch Drive Module
High-power MOSFET Trigger Switch Drive Module
50.00 EGP -
Relay Module 1 Channel 5V
The Single Channel Relay Module is a convenient board that can be used to control high voltage, high current loads such as motor, solenoid valves, lamps, and AC load.
It is designed to interface with microcontrollers such as Arduino, PIC and etc.
The relays terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes with a LED to indicate the status of the relay.
50.00 EGPRelay Module 1 Channel 5V
50.00 EGP -
12V Delay Timer Switch Adjustable
This 12V Delay Timer Switch Adjustable 0-10sec is one kind of popular switch module. You can use it control any devices on or off. This is a DC12V controlled 1 channel timer relay module. It has a NE555 timer chip on the board. You can adjust delay time(0-10s) by rotating the potentiometer. When this relay get powered it will delay several seconds before relay turn on.
Note: Recommended power + series with a diode to protect the circuit.
45.00 EGP12V Delay Timer Switch Adjustable
45.00 EGP -
12V Battery Level LED Indicator
XD-82B 12V Battery Level Indicator Module 4 Paragraph 4 onboard Battery Indicator LED Lights.
Monitor the level of your 12v battery and know when it’s running low with this small LED battery level indicator.
45.00 EGP12V Battery Level LED Indicator
45.00 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories