-
Relay Module 1 Channel 5V
The Single Channel Relay Module is a convenient board that can be used to control high voltage, high current loads such as motor, solenoid valves, lamps, and AC load.
It is designed to interface with microcontrollers such as Arduino, PIC and etc.
The relays terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes with a LED to indicate the status of the relay.
50.00 EGPRelay Module 1 Channel 5V
50.00 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP -
I2C Arduino Serial Module For LCD 16*2
This is I2C Arduino Serial Module For LCD board that can be connected to a standard HD44780 compatible 16×2 , 20×4 or 20×2 Character Display Module that supports 4 bit mode.This board has a PCF8574 I2C chip that converts I2C serial data to parallell data for the LCD display.
80.00 EGPI2C Arduino Serial Module For LCD 16*2
80.00 EGP -
GY-521 MPU6050 Triple 3-Axis Accelerometer Gyroscope I2C
The MPU6050 contains both a 3-Axis Gyroscope and a 3-Axis accelerometer allowing measurements of both independently, but all based around the same axes, thus eliminating the problems of cross-axis errors when using separate devices.
150.00 EGP -
12V Delay Timer Switch Adjustable
This 12V Delay Timer Switch Adjustable 0-10sec is one kind of popular switch module. You can use it control any devices on or off. This is a DC12V controlled 1 channel timer relay module. It has a NE555 timer chip on the board. You can adjust delay time(0-10s) by rotating the potentiometer. When this relay get powered it will delay several seconds before relay turn on.
Note: Recommended power + series with a diode to protect the circuit.
45.00 EGP12V Delay Timer Switch Adjustable
45.00 EGP -
Micro SD Card Module
Micro SD card mini TF card reader module SPI interfaces with level converter chip
50.00 EGPMicro SD Card Module
50.00 EGP -
Relay Module 2 Channel 5V (high/low) level trigger
Relay Module 2 Channel 5V is a LOW Level 5V 2-channel relay interface board, and each channel needs a 20mA driver current. It can be used to control various appliances and equipment with large current. It is equipped with high-current relays that work under AC 250 V -10 A or DC 30 V 10 A. It has a standard interface that can be controlled directly by microcontroller
80.00 EGP -
-
Rgb Led Module
- RGB LED is a light emitting diode that displays just about any color by manipulating the intensities of either the Red, the Green or the Blue LED.
10.00 EGPRgb Led Module
10.00 EGP -
Lipo Battery Voltage Tester / Low Voltage Buzzer Alarm
LIPO Battery Voltage Tester and low voltage buzzer alarm combo is easy to use.
Li-Po Battery Voltage Buzzer+Indicator: directly plug it into your operating battery, it will monitor the conditions of your battery all the time, so your batteries shall remain within safe operating voltage range at all times.
55.00 EGP -
NE555 Adjustable Frequency Pulse Generator Module
This is a square wave pulse generator module based on the ubiquitous NE555 timer IC. The module can be powered from a wide power supply range (5 to 12V) and will produce a continuous square wave output between 4Hz to 1.3KHz which can be set by on on-board multi-turn potentiometer. Module has ten-turn frequency adjustment control and power on LED. Useful for applications where an approximate frequency clock source is required such as for stepper motor step generation etc
35.00 EGP -
3D Printer Optical End Stop Switch Module
3D Printer Optical End Stop Switch Module
Key Features and Enhancements:
- High-Quality Cable: The module comes with a 22AWG cable line featuring thick copper wire. This high-quality cable ensures stable and reliable connections.
- Secure Connection: The cable line is designed to be securely attached, making it resistant to accidental disconnection during operation. This feature enhances the overall safety and reliability of the module.
- Versatile Compatibility: This optical endstop switch is compatible with a wide range of 3D printers, including CNC 3D Printer RepRap, Makerbot, Prusa, Mendel, and RAMPS End-stop. It is also suitable for various CNC and 3D tools, making it a versatile solution for different applications.
- Precise Optical Sensing: The optical endstop employs advanced optical sensing technology to provide precise and accurate detection. This ensures that your 3D printer or CNC machine can stop or switch positions with exceptional accuracy.
Specifications:
- Cable Length: 50cm (customizable options available)
- Current Rating: 2A
- Voltage Rating: 300V
- Operating Temperature Range: -20°C to 80°C (-4°F to 176°F)
- Module Dimensions: 33.02mm x 10mm x 8mm (L x W x H)
25.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories