-
-
Hi Link AC-DC Module 220Vac to 12Vdc “HLK-PM12”
HLK-PM12 is a ultra-compact power module. It is designed to meet the requirements of EMC and Safety Test. It can use in IOT project, Smart home and so on.88.00 EGP -
Hi Link AC-DC Module 220Vac to 3.3Vdc “HLK-PM03”
Hi Link AC-DC Module 220Vac to 3.3Vdc “HLK-PM03”
-
AC-DC 220V To 3.3Visolating Switch Power Supply Module/ Step-Down Module
-
Output Overload And Short Circuit Protection
-
Low Power Consumption, Environmental Protection, No-Load Loss <0.1W
-
The Product Is Designed to Meet the Requirements of EMC And Safety Test
-
It can use in IOT project, Smart home and so on.
88.00 EGP -
-
Hi Link AC-DC Module 220Vac to 5Vdc “HLK-PM01”
HLK-PM01 is a ultra-compact power module. It is designed to meet the requirements of EMC and Safety Test. It can use in IOT project, Smart home and so on.88.00 EGP -
High-power MOSFET Trigger Switch Drive Module
High-power MOSFET Trigger Switch Drive Module
50.00 EGP -
HW-183 Board DC-DC Step Up Power Module 2A B6287
HW-183 Board DC-DC Step Up Power Module 2A B6287
- The whole network’s smallest adjustable boost module can be easily installed in a variety of small equipment.
- The module supports Micro USB input, a USB charger or mobile power supply can easily get to it 9V, 12V, 15V, 18V, 24V, easy to use.
32.00 EGP -
HX711 Weighing Scale Analog to Digital Converter 24 bit
The Load Cell Amplifier and ADC (Analog-to-Digital Converter) Module is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the module to your microcontroller you will be able to read the changes in the resistance of the load cell and with some calibration you’ll be able to get very accurate weight measurements. This can be handy for creating your own industrial scale, process control, or simple presence detection.
The HX711 uses a two wire interface (Clock and Data) for communication. Any microcontroller’s GPIO pins should work and numerous libraries have been written making it easy to read data from the HX711. The module communicates with the host computer through TTL 232.
55.00 EGP -
I2C Arduino Serial Module For LCD 16*2
This is I2C Arduino Serial Module For LCD board that can be connected to a standard HD44780 compatible 16×2 , 20×4 or 20×2 Character Display Module that supports 4 bit mode.This board has a PCF8574 I2C chip that converts I2C serial data to parallell data for the LCD display.
80.00 EGPI2C Arduino Serial Module For LCD 16*2
80.00 EGP -
Infrared Flame Sensor Module – 4 pin
The Flame Sensor Module can detect flames in the 760 – 1100 nanometer wavelength range. Small flames like a lighter flame can be detected at roughly 0.8m. The detection angle is roughly 60 degrees and the sensor is particularly sensitive to the flame spectrum.
An on-board LM393 op-amp is used as a comparator to adjust the sensitivity level. The sensor has a digital and analog output and sensitivity can be adjusted via the blue potentiometer.
This Flame Sensor Module is used to detect fire/flame source or other light sources of the wavelength in the range of 760nm – 1100 nm. It is based on the YG1006 sensor which is a high speed and high sensitive NPN silicon phototransistor. Due to its black epoxy, the sensor is sensitive to infrared radiation.
The sensor can be a great addition in a firefighting robot, it can be used as a robot eyes to find the fire source. When the sensor detects flame the Signal LED will light up and the D0 pin goes LOW.
The module has 2 outputs: Analogue, which gives a real-time voltage output signal on thermal resistance, and digital which allows temperature thresholds to be set via a potentiometer.
Features :
- High Photo Sensitivity
- Fast Response Time
- Sensitivity adjustable
- Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
- Detection range: up to 100 cm.
- Adjustable detection range.
- Detection angle about 60 degrees, it is sensitive to the flame spectrum.
- Comparator chip LM393 makes module readings stable.
- Operating voltage 3.3V-5V.
- Digital and Analog Output.
- Power indicator and digital switch output indicator.
Package Includes :
1 x Flame Sensor Module
35.00 EGPInfrared Flame Sensor Module – 4 pin
35.00 EGP -
Infrared Remote Control and Receiver
IR Infrared Remote Control Module Wireless Receiver Module DIY Kit for Arduino for Raspberry Pi
33.00 EGPInfrared Remote Control and Receiver
33.00 EGP -
Inverter Module DC 12V to AC 110V 175V 220V – 150W
150W converter DC 12V TO AC 220V inverter boost module step up board
170.00 EGP -
IRF520 MOSFET Driver Module
IRF520 MOSFET Driver Module
27.50 EGPIRF520 MOSFET Driver Module
27.50 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories