-
MCP2515 CAN Bus Module Board TJA1050 Receiver SPI For 51 MCU
The MCP2515 Module adopts CAN controller MCP2515, and TJA1050 high-speed CAN transceiver. Microchip MCP2515 independent CAN protocol controller, support CAN V2.0B regulation. The connection between MCP2515 and MCU is through SPI.
230.00 EGP -
ADS1115 16-Bit ADC – 4 Channel with Programmable Gain Amplifier
For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 16 bit converter.
95.00 EGP -
NE555 Adjustable Frequency Pulse Generator Module
This is a square wave pulse generator module based on the ubiquitous NE555 timer IC. The module can be powered from a wide power supply range (5 to 12V) and will produce a continuous square wave output between 4Hz to 1.3KHz which can be set by on on-board multi-turn potentiometer. Module has ten-turn frequency adjustment control and power on LED. Useful for applications where an approximate frequency clock source is required such as for stepper motor step generation etc
35.00 EGP -
Rgb Led Module
- RGB LED is a light emitting diode that displays just about any color by manipulating the intensities of either the Red, the Green or the Blue LED.
10.00 EGPRgb Led Module
10.00 EGP -
SD Card Module, SPI Interface
This is a wonderful little Arduino to SD card interface module.Through programming, you can read and write to the SD card using your arduino.If you are feeling adventurous, this is truly an interesting board to work with and learn from.It is easily interfaced as a peripheral to your arduino sensor shield module.
55.00 EGPSD Card Module, SPI Interface
55.00 EGP -
Relay Module 8 Channel 5V
This is a 5V 8-Channels Relay module, It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and MSP430.
8 relays are included in this module, with “NC” ports means “Normally connected to COM” and “NO” ports means “Normally open to COM”. This module also equipped with 8 LEDS to show the status of relays
195.00 EGPRelay Module 8 Channel 5V
195.00 EGP -
2 Channel 5V DC Relay Module Solid State Low Level trigger
5V solid state relay 240V 2A, output with resistive fuse 240V 2A
95.00 EGP -
Relay Module 2 Channel 5V (high/low) level trigger
Relay Module 2 Channel 5V is a LOW Level 5V 2-channel relay interface board, and each channel needs a 20mA driver current. It can be used to control various appliances and equipment with large current. It is equipped with high-current relays that work under AC 250 V -10 A or DC 30 V 10 A. It has a standard interface that can be controlled directly by microcontroller
80.00 EGP -
Relay Module 1 Channel 5V
The Single Channel Relay Module is a convenient board that can be used to control high voltage, high current loads such as motor, solenoid valves, lamps, and AC load.
It is designed to interface with microcontrollers such as Arduino, PIC and etc.
The relays terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes with a LED to indicate the status of the relay.
50.00 EGPRelay Module 1 Channel 5V
50.00 EGP -
Relay Module 16 Channel 5V
Relay Module 16 Channel 5V
231.00 EGPRelay Module 16 Channel 5V
231.00 EGP -
Reed Switch Module
Reed switch is a kind of passive electronic switching component with contacts with a simple structure, small size and easy to control. It consists of a sealed glass envelope where there are two ferrous elastic reeds and is filled with inert gas called rhodium
35.00 EGPReed Switch Module
35.00 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories