-
HC-06 Bluetooth Module
- The HC-06 is a class-2 slave Bluetooth module.
- It is designed to enable wireless serial communication between microcontroller (like Arduino) and other Bluetooth enabled devices.
- All data received through the serial input is immediately transmitted wirelessly by the module, when the module receives some wireless data from the master device (like a smartphone), this data is sent out through the serial interface.
- A Logic Level Converter is recommended to convert the 5v input to 3.3V.
200.00 EGPHC-06 Bluetooth Module
200.00 EGP -
Hi Link AC-DC Module 220Vac to 12Vdc “HLK-PM12”
HLK-PM12 is a ultra-compact power module. It is designed to meet the requirements of EMC and Safety Test. It can use in IOT project, Smart home and so on.88.00 EGP -
Hi Link AC-DC Module 220Vac to 3.3Vdc “HLK-PM03”
Hi Link AC-DC Module 220Vac to 3.3Vdc “HLK-PM03”
-
AC-DC 220V To 3.3Visolating Switch Power Supply Module/ Step-Down Module
-
Output Overload And Short Circuit Protection
-
Low Power Consumption, Environmental Protection, No-Load Loss <0.1W
-
The Product Is Designed to Meet the Requirements of EMC And Safety Test
-
It can use in IOT project, Smart home and so on.
88.00 EGP -
-
Hi Link AC-DC Module 220Vac to 5Vdc “HLK-PM01”
HLK-PM01 is a ultra-compact power module. It is designed to meet the requirements of EMC and Safety Test. It can use in IOT project, Smart home and so on.88.00 EGP -
High-power MOSFET Trigger Switch Drive Module
High-power MOSFET Trigger Switch Drive Module
50.00 EGP -
HX711 Weighing Scale Analog to Digital Converter 24 bit
The Load Cell Amplifier and ADC (Analog-to-Digital Converter) Module is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the module to your microcontroller you will be able to read the changes in the resistance of the load cell and with some calibration you’ll be able to get very accurate weight measurements. This can be handy for creating your own industrial scale, process control, or simple presence detection.
The HX711 uses a two wire interface (Clock and Data) for communication. Any microcontroller’s GPIO pins should work and numerous libraries have been written making it easy to read data from the HX711. The module communicates with the host computer through TTL 232.
55.00 EGP -
I2C Arduino Serial Module For LCD 16*2
This is I2C Arduino Serial Module For LCD board that can be connected to a standard HD44780 compatible 16×2 , 20×4 or 20×2 Character Display Module that supports 4 bit mode.This board has a PCF8574 I2C chip that converts I2C serial data to parallell data for the LCD display.
80.00 EGPI2C Arduino Serial Module For LCD 16*2
80.00 EGP -
IRF520 MOSFET Driver Module
IRF520 MOSFET Driver Module
27.50 EGPIRF520 MOSFET Driver Module
27.50 EGP -
ISD1820 Recording And Playback Module 10 Seconds
This ISD1820 Voice Recorder/Playback Module reproduces high-quality, natural voice and audio from the recorded audio by Mic or driven through Microcontroller.
Because of its dual operation mode (Standalone and Microcontroller driven), we can easily use this as per requirement and with a slight change of the onboard resistor, we can get flexibility in the sampling frequency of the recording duration & quality.
83.00 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP -
Lipo Battery Voltage Tester / Low Voltage Buzzer Alarm
LIPO Battery Voltage Tester and low voltage buzzer alarm combo is easy to use.
Li-Po Battery Voltage Buzzer+Indicator: directly plug it into your operating battery, it will monitor the conditions of your battery all the time, so your batteries shall remain within safe operating voltage range at all times.
55.00 EGP -
LM2577 2.5A DC-DC Step UP LED Voltmeter 3-34 to 4-35V Adjustable Boost Converter module
The LM2577 2.5A DC-DC Step UP LED Voltmeter 3-34 to 4-35V Adjustable Boost Converter module is a 150 KHz fixed frequency PWM buck (step-down) DC/DC module. Requiring a minimum number of external components, these regulators are cost-effective, and simple to use.
77.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories