-
DC-DC Adjustable Step-Down Power Supply Module -XL4005 5A 75W DSN5000
XL4005 is a 300KHz fixed frequency PWM buck (step-down) DC/DC converter, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation. Requiring a minimum number of external components, the regulator is simple to use and include internal frequency compensation and a fixed-frequency oscillator.
48.00 EGP -
HC-05 Bluetooth Module
Very simple Bluetooth module to connect it with your microcontroller, Arduino, Raspberry Pi, or any MCU board using the TTL UART interface
This serial bluetooth module can work as either master or slave. This module also includes the base board, not only the core board, most functions are pre-set, so only the serial port communication is available but it’s more easy to use. It can be used also with arduino or Microcontroller.
250.00 EGPHC-05 Bluetooth Module
250.00 EGP -
-
Relay Module 1 Channel 5V
The Single Channel Relay Module is a convenient board that can be used to control high voltage, high current loads such as motor, solenoid valves, lamps, and AC load.
It is designed to interface with microcontrollers such as Arduino, PIC and etc.
The relays terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes with a LED to indicate the status of the relay.
50.00 EGPRelay Module 1 Channel 5V
50.00 EGP -
MAX485 TTL To RS485 Converter Module
5V MAX485 TTL To RS485 Converter Module Board For Arduino
60.00 EGPMAX485 TTL To RS485 Converter Module
60.00 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP -
I2C Arduino Serial Module For LCD 16*2
This is I2C Arduino Serial Module For LCD board that can be connected to a standard HD44780 compatible 16×2 , 20×4 or 20×2 Character Display Module that supports 4 bit mode.This board has a PCF8574 I2C chip that converts I2C serial data to parallell data for the LCD display.
80.00 EGPI2C Arduino Serial Module For LCD 16*2
80.00 EGP -
ESP8266 ESP-12F Wifi Transceiver Wireless Module
The Latest ESP-12F ESP8266 Wi-Fi Module AP & Station Remote Serial Wireless IoT Board is an integrated chip designed for the needs of a new connected world.
It can handle all the necessary overhead for communicating with your network, such as TCP/IP stack and communicating with your 802.11 networks.
It is completely addressable over SPI and UART protocols allowing you to connect your sensors or project directly to it through its GPIO’s. ESP8266 is a low-cost Wi-Fi chip with a full TCP/IP stack and MCU (Micro Controller Unit) capability.
ESP8266 Serial Wi-Fi Wireless Transceiver Module is a self-contained SOC with an integrated TCP/IP protocol stack that can give any microcontroller access to your Wi-Fi network.
ESP8266 Serial Wifi Wireless Transceiver Module is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor.
Each ESP8266 module comes pre-programmed with an AT command set firmware, meaning, you can simply hook this up to your Arduino device and get about as much Wi-Fi-ability as a Wi-Fi Shield offers.
The ESP8266 module is an extremely cost-effective board with a huge, and ever-growing, community.
ESP8266 Serial Wi-Fi Wireless Transceiver Module has a powerful enough onboard processing and storage capability that allows it to be integrated with the sensors and other application-specific devices through its GPIOs with minimal development up-front and minimal loading during runtime.
Its high degree of on-chip integration allows for minimal external circuitry, including the front-end module, which is designed to occupy a minimal PCB area.
The ESP8266 supports APSD for VoIP applications and Bluetooth co-existence interfaces, it contains a self-calibrated RF allowing it to work under all operating conditions and requires no external RF parts.
185.00 EGP -
GY-521 MPU6050 Triple 3-Axis Accelerometer Gyroscope I2C
The MPU6050 contains both a 3-Axis Gyroscope and a 3-Axis accelerometer allowing measurements of both independently, but all based around the same axes, thus eliminating the problems of cross-axis errors when using separate devices.
150.00 EGP -
DS1307 RTC Module 24C32 Memory
DS1307 RTC Module 24C32 Memory
45.00 EGPDS1307 RTC Module 24C32 Memory
45.00 EGP -
12V Delay Timer Switch Adjustable
This 12V Delay Timer Switch Adjustable 0-10sec is one kind of popular switch module. You can use it control any devices on or off. This is a DC12V controlled 1 channel timer relay module. It has a NE555 timer chip on the board. You can adjust delay time(0-10s) by rotating the potentiometer. When this relay get powered it will delay several seconds before relay turn on.
Note: Recommended power + series with a diode to protect the circuit.
45.00 EGP12V Delay Timer Switch Adjustable
45.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories