-
Xbee 2Mw 120M
xbee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol.
Series 2 modules allow you to create complex mesh networks based on the Xbee ZB ZigBee mesh firmware.
These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
These are essentially the same hardware as the older Series 2.5 but have updated firmware.
They will work with Series 2.5 modules if you update the firmware through X-CTU
330.00 EGPXbee 2Mw 120M
330.00 EGP -
Boost Step-up Power Module High-voltage Generator DC 3V-6V to 1000KV
Boost Step-up Power Module
300.00 EGP -
MAX6675 Module for Thermocouple K Type
This K Type Thermocouple can be used to measure temperatures up to 600 degree Celsius! Great for industrial projects, 3D Printers, DIY and hobby projects which require a high temperature to be measured.
285.00 EGPMAX6675 Module for Thermocouple K Type
285.00 EGP -
4 Channel 5V Relay Module Board Shield for Arduino
4 Channel 5V Relay Module Board Shield for Arduino
- This 5V 4 Relay Shield Module is a small current signal control power equipment commonly used electronic module
- Enabling high-power single-chip control devices are widely used in SCM system to make smart home project
- Can be directly plugged into the compatible the use of various types of motherboards, eliminating the patch cable troubles.
- This relay module is 5V active low.
- It is a 4-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc.
- It is also able to control various appliances and other equipment with large current. Standard interface can be directly connected with microcontrollers.
- Red working status indicator lights are conducive to the safe use.
- Widely used for all MCU control, industrial sector, PLC control, and smart home control.
- Working voltage: 5V
- Channel: 4 channel
- Color: Blue
- Item size: approx. 7.1 x 5 x 1.3cm
- Net weight: 41.3g
275.00 EGP -
IBT-2 Motor Driver 43A
IBT-2 43A H-Bridge Motor Driver Module the drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection.
motor driver H-bridge driver circuit, with strong drive and braking effect, use 74HC244 chip effectively isolate the microcontroller and the motor drive High Current up to 43A
IBT-2 motor driver is a fully integrated high current H bridge module for motor drive applications.
Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with current sense, slew rate adjustment, dead time generation and protection against overtemperature, overvoltage, under voltage, overcurrent and short circuit.
provides a cost optimized solution for protected high current PWM motor drives with very low board space consumption.
The 43a motor driver IBT-2 H-bridge module is an inexpensive, high power motor driver based on two BTS7960 chips
This driver 43a motor driver uses two high current half bridge Infineon BTS 7960 chip for motor drive applications. Interfacing to a microcontroller is made easy using this driver which features current sensing, slew rate adjustment and protection against over temperature, overvoltage, under voltage, over current and short circuit.
This small size driver provides a cost optimized solution for protected high current PWM motor drives.
275.00 EGPIBT-2 Motor Driver 43A
275.00 EGP -
HC-12 Wirless Transceiver Module (1KM)
Transceiver Module
HC-12 Wireless Transceiver Module (SI4438, 433MHz, 1km)
250.00 EGPHC-12 Wirless Transceiver Module (1KM)
250.00 EGP -
HC-06 Bluetooth Module
- The HC-06 is a class-2 slave Bluetooth module.
- It is designed to enable wireless serial communication between microcontroller (like Arduino) and other Bluetooth enabled devices.
- All data received through the serial input is immediately transmitted wirelessly by the module, when the module receives some wireless data from the master device (like a smartphone), this data is sent out through the serial interface.
- A Logic Level Converter is recommended to convert the 5v input to 3.3V.
200.00 EGPHC-06 Bluetooth Module
200.00 EGP -
Lithium Battery Charger Protection Module (BMS) 5S 15A 21V
5S 15A Li-ion Lithium Battery 18650 Charger PCB BMS 18.5V 21V Cell Protection Board Integrated Circuits
190.00 EGP -
ESP8266 ESP-12F Wifi Transceiver Wireless Module
The Latest ESP-12F ESP8266 Wi-Fi Module AP & Station Remote Serial Wireless IoT Board is an integrated chip designed for the needs of a new connected world.
It can handle all the necessary overhead for communicating with your network, such as TCP/IP stack and communicating with your 802.11 networks.
It is completely addressable over SPI and UART protocols allowing you to connect your sensors or project directly to it through its GPIO’s. ESP8266 is a low-cost Wi-Fi chip with a full TCP/IP stack and MCU (Micro Controller Unit) capability.
ESP8266 Serial Wi-Fi Wireless Transceiver Module is a self-contained SOC with an integrated TCP/IP protocol stack that can give any microcontroller access to your Wi-Fi network.
ESP8266 Serial Wifi Wireless Transceiver Module is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor.
Each ESP8266 module comes pre-programmed with an AT command set firmware, meaning, you can simply hook this up to your Arduino device and get about as much Wi-Fi-ability as a Wi-Fi Shield offers.
The ESP8266 module is an extremely cost-effective board with a huge, and ever-growing, community.
ESP8266 Serial Wi-Fi Wireless Transceiver Module has a powerful enough onboard processing and storage capability that allows it to be integrated with the sensors and other application-specific devices through its GPIOs with minimal development up-front and minimal loading during runtime.
Its high degree of on-chip integration allows for minimal external circuitry, including the front-end module, which is designed to occupy a minimal PCB area.
The ESP8266 supports APSD for VoIP applications and Bluetooth co-existence interfaces, it contains a self-calibrated RF allowing it to work under all operating conditions and requires no external RF parts.
185.00 EGP -
GY-61 DXL335 3-Axis Accelerometer Module
GY-61 ADXL335 Module is a small, thin, low-power, complete 3-axis accelerometer with signal conditioned voltage outputs.
The ADXL335 Module 3-axis Analog Output Accelerometer measures acceleration with a minimum full-scale range of ±3 g.
It can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion, shock, or vibration.
This breakout board comes with an onboard voltage regulator and works at both 3.3V & 5V (3-5V).
An accelerometer is an electro-mechanical device that will measure acceleration forces.
These forces may be static, like the constant force of gravity pulling at your feet, or they could be dynamic – caused by moving or vibrating the accelerometer.
180.00 EGPGY-61 DXL335 3-Axis Accelerometer Module
180.00 EGP -
ESP8266 ESP-01 with USB adapter WiFi module
This module is a USB programmer for ESP8266 modules of type ESP-01.
175.00 EGPESP8266 ESP-01 with USB adapter WiFi module
175.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories