-
Relay Module 2 Channel 12V (high/low) level trigger
This is a HIGH/LOW Level 12V 2-channel relay interface board, and each channel needs a 20mA driver current. It can be used to control various appliances and equipment with large current. It is equipped with high-current relays that work under AC 250V 10A or DC 30V 10A. It has a standard interface that can be controlled directly by microcontroller
85.00 EGP -
Led Matrix 8×8 With MAX7219 Module
The MAX7219 Dot Led Matrix Module is a serial input common-cathode driver that interfaces micro-controllers to LED matrices
50.00 EGPLed Matrix 8×8 With MAX7219 Module
50.00 EGP -
CH376S U Disk Read Write Module For USB Control Transfer
CH376 is common a USB bus interface chip, with 8 bit data bus and reading, writing and chip select lines and interrupt output, can easily attached to the system bus of the single chip microcomputer /DSP/MCU/MPU controller.
110.00 EGP -
Relay Module 1 Channel 5V
The Single Channel Relay Module is a convenient board that can be used to control high voltage, high current loads such as motor, solenoid valves, lamps, and AC load.
It is designed to interface with microcontrollers such as Arduino, PIC and etc.
The relays terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes with a LED to indicate the status of the relay.
50.00 EGPRelay Module 1 Channel 5V
50.00 EGP -
I2C Arduino Serial Module For LCD 16*2
This is I2C Arduino Serial Module For LCD board that can be connected to a standard HD44780 compatible 16×2 , 20×4 or 20×2 Character Display Module that supports 4 bit mode.This board has a PCF8574 I2C chip that converts I2C serial data to parallell data for the LCD display.
80.00 EGPI2C Arduino Serial Module For LCD 16*2
80.00 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP -
Mini 5V Traffic Light LED Display Module for Arduino Red Yellow Green 5mm LED
Mini 5V Traffic Light LED Display Module for Arduino Red Yellow Green 5mm LED RGB -Traffic Light for Traffic Light System Model
30.00 EGP -
Micro-USB Female Breakout Module
A Female MicroUSB port with breakout board so you can solder on wires or header pins and integrate into any project.
15.00 EGPMicro-USB Female Breakout Module
15.00 EGP -
GY-521 MPU6050 Triple 3-Axis Accelerometer Gyroscope I2C
The MPU6050 contains both a 3-Axis Gyroscope and a 3-Axis accelerometer allowing measurements of both independently, but all based around the same axes, thus eliminating the problems of cross-axis errors when using separate devices.
150.00 EGP -
MAX6675 Module for Thermocouple K Type
This K Type Thermocouple can be used to measure temperatures up to 600 degree Celsius! Great for industrial projects, 3D Printers, DIY and hobby projects which require a high temperature to be measured.
285.00 EGPMAX6675 Module for Thermocouple K Type
285.00 EGP -
Relay Module 4 Channel – 5V DC
Relay Module 5Vdc – 4 Relay For Arduino & MCU H/L Trigger
150.00 EGPRelay Module 4 Channel – 5V DC
150.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories