-
4 Channels Dc Servo Stepper Motor Driver Module For Arduino L298
4 Channels Dc Servo Stepper Motor Driver Module For Arduino L298
242.00 EGP -
TB6560 CNC 3-Axis Driver 3.5A
TB6560 stepper motor driver can drive up to 3 stepper motors with 3.5 A peak current for each motor. It is also equipped with spindle relay output and can handle a spindle. It has micro-stepping capability up to 1/16 micro-step.
The driver is integrated with break output board (so you do not need one) and can be connected directly to the parallel port. In addition, it has a manual control port interface for manual control of your motors.
The 3-axis driver uses Toshiba TB6560AHQ chip and equipped with optical isolation with dc-dc power supply isolation for full protection. Finally, this driver is compatible with most parallel software MACH3, KCAM4 etc.!
825.00 EGPTB6560 CNC 3-Axis Driver 3.5A
825.00 EGP -
Stepper Motor ULN2003 Driver Module
The ULN2003 stepper motor driver PCB provides a direct drive interface between your microcontroller and stepper motor. The PCB provides 4 inputs for connection to your microcontroller, power supply connection for the stepper motor voltage, and ON/OFF jumper, a direct connect stepper motor header and 4 LEDs to indicate stepping state
35.00 EGPStepper Motor ULN2003 Driver Module
35.00 EGP -
MA860H Stepper Motor Driver
MA860H Stepper Motor Driver is a high-performance stepper driver implemented with pure-sinusoidal current control technology. The MA860H Digital Stepper Motor Driver 50-110 VDC with 1.8-7.5A can be used to drive 2-phase or 4-phase motors (from “NEMA 17” or “NEMA 34” size) with less noise and heat. And it can provide better performances at high speed than most of the drivers in the markets.
It works with 36-110VDC/24-80VAC voltage and can provide max 7.2A peak current. You can set the DIP switches to get the current and micro steps you need.
1,599.00 EGP1,660.00 EGPMA860H Stepper Motor Driver
1,599.00 EGP1,660.00 EGP -
L293D 4-DC Motor Driver
DC Motor Driver
The drive module can directly drive four DC motors, drive the car chassis is 4WD 4 choice. Driving battery big up to 1A generally smart car motor current 100-300MA only four are sufficient to meet the control requirements.
The circuit stability. Can directly drive 4-way 3-16V DC motor, and provides a 5V output interface (input as little as 6V), You can give 5V microcontroller circuit system power supply (low ripple factor), Support 3.3V MCU ARM control, You can easily control DC motor speed and direction can be controlled two-phase stepper motor, 5-wire 4-phase stepper motor.
165.00 EGPL293D 4-DC Motor Driver
165.00 EGP -
IBT-2 Motor Driver 43A
IBT-2 43A H-Bridge Motor Driver Module the drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection.
motor driver H-bridge driver circuit, with strong drive and braking effect, use 74HC244 chip effectively isolate the microcontroller and the motor drive High Current up to 43A
IBT-2 motor driver is a fully integrated high current H bridge module for motor drive applications.
Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with current sense, slew rate adjustment, dead time generation and protection against overtemperature, overvoltage, under voltage, overcurrent and short circuit.
provides a cost optimized solution for protected high current PWM motor drives with very low board space consumption.
The 43a motor driver IBT-2 H-bridge module is an inexpensive, high power motor driver based on two BTS7960 chips
This driver 43a motor driver uses two high current half bridge Infineon BTS 7960 chip for motor drive applications. Interfacing to a microcontroller is made easy using this driver which features current sensing, slew rate adjustment and protection against over temperature, overvoltage, under voltage, over current and short circuit.
This small size driver provides a cost optimized solution for protected high current PWM motor drives.
275.00 EGPIBT-2 Motor Driver 43A
275.00 EGP -
30A Dual Motor Driver High-Power H Bridge
30A Dual Motor Driver High-Power H Bridge
440.00 EGP30A Dual Motor Driver High-Power H Bridge
440.00 EGP -
10A Single Channel DC Motor Drive Board 350W
10A Single Channel DC Motor Drive Board Module Industrial Large Power MOSFET Single H Bridge w/ Braking
242.00 EGP10A Single Channel DC Motor Drive Board 350W
242.00 EGP -
10A Double Way Motor Driver
10A Double Way Motor Driver
385.00 EGP10A Double Way Motor Driver
385.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories