Search Results for "module"
-
USB to UART/ESP8266 Adapter Programmer for ESP-01 WIFI Modules with CH340G Chip
USB to UART/ESP8266 Adapter Programmer for ESP-01 WIFI Modules with CH340G Chip
- Driver Chip: CH340G
- Supports all basic windows versions.
- The adapter plate integrated 1000μF solid capacitors to ensure the current supply
- The power supply will not be a problem to make WIFI module crashes unresponsive.
- Using 3225 SMD crystal oscillator, improve the stability of serial work, on a beautiful and tall.
- Working voltage: 4.5V – 5.5V (Onboard 3.3v LDO Regulator)
- Working current: 300mA (LDO regulator can supply)
40.00 EGP -
65.00 EGP
75.00 EGPMini Motor Drive Shield Expansion Board L293D Module
65.00 EGP75.00 EGP -
7″ Color TFT LCD Module MCU 800×480 – LMT070DICFWD-NJA
– resolution: 800×480– Interface: MCUVoltage: 5V– Temperature: -20°C ~ 70°C– Outline: 190.0mm x 112.0mm x 13.3mm– Size: 7″inc– Active Area: 154.08mm x 85.92mm– Touch Screen: RTP1,700.00 EGP -
Infrared Flame Sensor Module – 4 pin
The Flame Sensor Module can detect flames in the 760 – 1100 nanometer wavelength range. Small flames like a lighter flame can be detected at roughly 0.8m. The detection angle is roughly 60 degrees and the sensor is particularly sensitive to the flame spectrum.
An on-board LM393 op-amp is used as a comparator to adjust the sensitivity level. The sensor has a digital and analog output and sensitivity can be adjusted via the blue potentiometer.
This Flame Sensor Module is used to detect fire/flame source or other light sources of the wavelength in the range of 760nm – 1100 nm. It is based on the YG1006 sensor which is a high speed and high sensitive NPN silicon phototransistor. Due to its black epoxy, the sensor is sensitive to infrared radiation.
The sensor can be a great addition in a firefighting robot, it can be used as a robot eyes to find the fire source. When the sensor detects flame the Signal LED will light up and the D0 pin goes LOW.
The module has 2 outputs: Analogue, which gives a real-time voltage output signal on thermal resistance, and digital which allows temperature thresholds to be set via a potentiometer.
Features :
- High Photo Sensitivity
- Fast Response Time
- Sensitivity adjustable
- Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
- Detection range: up to 100 cm.
- Adjustable detection range.
- Detection angle about 60 degrees, it is sensitive to the flame spectrum.
- Comparator chip LM393 makes module readings stable.
- Operating voltage 3.3V-5V.
- Digital and Analog Output.
- Power indicator and digital switch output indicator.
Package Includes :
1 x Flame Sensor Module
35.00 EGPInfrared Flame Sensor Module – 4 pin
35.00 EGP -
BMP280 Barometric Pressure & Altitude Sensor I2C/SPI Module 3.3V
Description
This BMP280 is a cheapest and tiny Atmospheric Sensor Breakout to measure barometric pressure, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BMP280 Breakout has been design to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
This module uses an environmental sensor manufactured by Bosch with temperature, barometric pressure sensor that is the next generation upgrade to the popular BMP085/BMP180/BMP183 Sensor. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI! This precision sensor from Bosch is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuracy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with ±1 meter accuracy.
The BMP280 is the next-generation of sensors, and is the upgrade to the BMP085/BMP180/BMP183 – with a low altitude noise of 0.25m and the same fast conversion time. It has the same specifications, but can use either I2C or SPI. For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.
Features:-
- Get more precise temperature, atmospheric pressure values, and approximate altitude data
- Enhancement of GPS navigation (e.g. time-tofirst-fix improvement, dead-reckoning, slope detection)
- Indoor navigation (floor detection, elevator detection)
- Outdoor navigation, leisure and sports applications
- Weather forecast
- Health care applications (e.g. spirometry)
- Vertical velocity indication (e.g. rise/sink speed)
- Libraries and tutorials available for Arduino and other micro controllers
- Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V
- Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C)
- Operating Pressure: 300 hPa to 1100 hPa
- Peak current: 1.12mA
- Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m
60.00 EGP -
2.8inch TFT LCD Module + Mini V3 STM32F103RBT6 Development Board + USB Cable
-
2.8inch LCD Module + USB Cable
-
Type: TFT
-
Model Number: MINI-STM32
-
CPU: STM32F103RBT6
1,250.00 EGP -
-
HW-183 Board DC-DC Step Up Power Module 2A B6287
HW-183 Board DC-DC Step Up Power Module 2A B6287
- The whole network’s smallest adjustable boost module can be easily installed in a variety of small equipment.
- The module supports Micro USB input, a USB charger or mobile power supply can easily get to it 9V, 12V, 15V, 18V, 24V, easy to use.
32.00 EGP -
ESP8266 ESP-01 with USB adapter WiFi module
This module is a USB programmer for ESP8266 modules of type ESP-01.
175.00 EGPESP8266 ESP-01 with USB adapter WiFi module
175.00 EGP -