-
GY-61 DXL335 3-Axis Accelerometer Module
GY-61 ADXL335 Module is a small, thin, low-power, complete 3-axis accelerometer with signal conditioned voltage outputs.
The ADXL335 Module 3-axis Analog Output Accelerometer measures acceleration with a minimum full-scale range of ±3 g.
It can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion, shock, or vibration.
This breakout board comes with an onboard voltage regulator and works at both 3.3V & 5V (3-5V).
An accelerometer is an electro-mechanical device that will measure acceleration forces.
These forces may be static, like the constant force of gravity pulling at your feet, or they could be dynamic – caused by moving or vibrating the accelerometer.
180.00 EGPGY-61 DXL335 3-Axis Accelerometer Module
180.00 EGP -
GY-65 BMP085 Atmospheric Pressure Altimeter Module
GY-65 BMP085 is a high precision, ultra-low power consumption pressure sensors, can be applied to mobile devices. Its performance, the absolute accuracy of the minimum can reach 0.03hPa, and very low power consumption, only 3A.
BMP085 powerful 8-pin ceramic-lead chip carrier (LCC) ultra-thin package, through the I2C bus can be connected directly with a variety of microprocessor.
72.00 EGP -
GY-88 IMU 10DOF MPU6050 + HMC5883L + BMP085
This IMU 10DOF is a motion tracking module. Its design is based on the sensor MPU6050,HMC5883L and BMP085.
The sensor MPU6050 which is the world’s first integrated 6-axis Motion Tracking device, that combines a 3-axis gyroscope, 3-axis accelerometer, and a Digital Motion Processor (DMP).
The Honeywell’s HMC5883L which is a 3-axis digital compass.
The BMP085 is a high-accuracy chip to detect barometric pressure and temperature.You can uses it in your DIY or your product,for example, Quadcopter, Self-Balancing Robot and so on.
220.00 EGPGY-88 IMU 10DOF MPU6050 + HMC5883L + BMP085
220.00 EGP -
High-power MOSFET Trigger Switch Drive Module
High-power MOSFET Trigger Switch Drive Module
50.00 EGP -
I2C Arduino Serial Module For LCD 16*2
This is I2C Arduino Serial Module For LCD board that can be connected to a standard HD44780 compatible 16×2 , 20×4 or 20×2 Character Display Module that supports 4 bit mode.This board has a PCF8574 I2C chip that converts I2C serial data to parallell data for the LCD display.
80.00 EGPI2C Arduino Serial Module For LCD 16*2
80.00 EGP -
IRF520 MOSFET Driver Module
IRF520 MOSFET Driver Module
27.50 EGPIRF520 MOSFET Driver Module
27.50 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP -
Lipo Battery Voltage Tester / Low Voltage Buzzer Alarm
LIPO Battery Voltage Tester and low voltage buzzer alarm combo is easy to use.
Li-Po Battery Voltage Buzzer+Indicator: directly plug it into your operating battery, it will monitor the conditions of your battery all the time, so your batteries shall remain within safe operating voltage range at all times.
55.00 EGP -
-
MCP2515 CAN Bus Module Board TJA1050 Receiver SPI For 51 MCU
The MCP2515 Module adopts CAN controller MCP2515, and TJA1050 high-speed CAN transceiver. Microchip MCP2515 independent CAN protocol controller, support CAN V2.0B regulation. The connection between MCP2515 and MCU is through SPI.
230.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories