-
S3003 Servo Motor
This is the Futaba S3003 Standard Servo.This basic servo is used in cars, boats, or where standard servos are used.This is the replacement for the following servos, S138,S148,S22,S38 and S12.This servo can produce high-current draw from your batteries.If using NiMH or LiPo batteries, make sure they are capableof delivering sufficient amps. 160.00 EGPS3003 Servo Motor
160.00 EGP -
Mg995 Gear Servo Motor/Digital Steering Gear 360 Degree
Mg995 Metal Gear Servo Motor/Digital Steering Gear 360 Degree
200.00 EGP -
Mg995 Gear Servo Motor / Digital Steering Gear 180 Degree
Mg995 Metal Gear Servo Motor / Digital Steering Gear 180 Degree
200.00 EGP -
Mg945 Metal Gear Servo Motor/Digital Steering Gear
MG945 12KG High Speed Torque Analog Metal Gear Servo for RC Drone Car Boat Helicopter RC Parts Servo.
143.00 EGP -
-
-
Bilge Pump 1100 GPH 12V
Bilge 1100 GPH 12V Electric Marine Water Submersible Pump for Yacht Boat Ship
850.00 EGPBilge Pump 1100 GPH 12V
850.00 EGP -
4 Channels Dc Servo Stepper Motor Driver Module For Arduino L298
4 Channels Dc Servo Stepper Motor Driver Module For Arduino L298
242.00 EGP -
DC Geared Motor Dual Shaft 3:12VDC 450RPM
Yellow Gear Motor 3V to 12V 176 RPM For Arduino
40.00 EGP -
TB6560 Stepper Motor Driver
TB6560 Stepper Motor Driver
550.00 EGPTB6560 Stepper Motor Driver
550.00 EGP -
TB6560 CNC 3 AXIS STEPPER MOTOR DRIVER CONTROLLER BOARD FOR MACH3 KCAM4 EMC2 36V
TB6560 CNC 3 AXIS STEPPER MOTOR DRIVER CONTROLLER BOARD FOR MACH3 KCAM4 EMC2 36V
650.00 EGP880.00 EGPTB6560 CNC 3 AXIS STEPPER MOTOR DRIVER CONTROLLER BOARD FOR MACH3 KCAM4 EMC2 36V
650.00 EGP880.00 EGP -
TB6560 CNC 3-Axis Driver 3.5A
TB6560 stepper motor driver can drive up to 3 stepper motors with 3.5 A peak current for each motor. It is also equipped with spindle relay output and can handle a spindle. It has micro-stepping capability up to 1/16 micro-step.
The driver is integrated with break output board (so you do not need one) and can be connected directly to the parallel port. In addition, it has a manual control port interface for manual control of your motors.
The 3-axis driver uses Toshiba TB6560AHQ chip and equipped with optical isolation with dc-dc power supply isolation for full protection. Finally, this driver is compatible with most parallel software MACH3, KCAM4 etc.!
825.00 EGPTB6560 CNC 3-Axis Driver 3.5A
825.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories