-
Cytron 13Amp 6V-30V DC Motor Driver
Cytron 13Amp
540.00 EGPCytron 13Amp 6V-30V DC Motor Driver
540.00 EGP -
DM860 Stepper Motor Driver
DM860 Microstep driver 2 phase 7.2A DC18-80V
1,485.00 EGPDM860 Stepper Motor Driver
1,485.00 EGP -
DRV8825 Stepper Motor Driver (md20b)
The DRV8825 stepper motor driver carrier is a breakout board for DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
120.00 EGPDRV8825 Stepper Motor Driver (md20b)
120.00 EGP -
IBT-2 Motor Driver 43A
IBT-2 43A H-Bridge Motor Driver Module the drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection.
motor driver H-bridge driver circuit, with strong drive and braking effect, use 74HC244 chip effectively isolate the microcontroller and the motor drive High Current up to 43A
IBT-2 motor driver is a fully integrated high current H bridge module for motor drive applications.
Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with current sense, slew rate adjustment, dead time generation and protection against overtemperature, overvoltage, under voltage, overcurrent and short circuit.
provides a cost optimized solution for protected high current PWM motor drives with very low board space consumption.
The 43a motor driver IBT-2 H-bridge module is an inexpensive, high power motor driver based on two BTS7960 chips
This driver 43a motor driver uses two high current half bridge Infineon BTS 7960 chip for motor drive applications. Interfacing to a microcontroller is made easy using this driver which features current sensing, slew rate adjustment and protection against over temperature, overvoltage, under voltage, over current and short circuit.
This small size driver provides a cost optimized solution for protected high current PWM motor drives.
275.00 EGPIBT-2 Motor Driver 43A
275.00 EGP -
-
L293D 4-DC Motor Driver
DC Motor Driver
The drive module can directly drive four DC motors, drive the car chassis is 4WD 4 choice. Driving battery big up to 1A generally smart car motor current 100-300MA only four are sufficient to meet the control requirements.
The circuit stability. Can directly drive 4-way 3-16V DC motor, and provides a 5V output interface (input as little as 6V), You can give 5V microcontroller circuit system power supply (low ripple factor), Support 3.3V MCU ARM control, You can easily control DC motor speed and direction can be controlled two-phase stepper motor, 5-wire 4-phase stepper motor.
165.00 EGPL293D 4-DC Motor Driver
165.00 EGP -
-
L297 DIP STEPPER MOTOR CONTROLLER
L297 DIP STEPPER MOTOR CONTROLLER
30.00 EGPL297 DIP STEPPER MOTOR CONTROLLER
30.00 EGP -
L298 DIP DUAL FULL BRIDGE DRIVER
L298 DIP DUAL FULL BRIDGE DRIVER
45.00 EGPL298 DIP DUAL FULL BRIDGE DRIVER
45.00 EGP -
-
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories