-
Relay 1 channel 30A 240VAC
30A relay module, normally open interface with maximum load: AC 240V/30A, DC 30V/30A
55.00 EGPRelay 1 channel 30A 240VAC
55.00 EGP -
Relay Module 1 Channel 5V
The Single Channel Relay Module is a convenient board that can be used to control high voltage, high current loads such as motor, solenoid valves, lamps, and AC load.
It is designed to interface with microcontrollers such as Arduino, PIC and etc.
The relays terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes with a LED to indicate the status of the relay.
50.00 EGPRelay Module 1 Channel 5V
50.00 EGP -
Relay Module 16 Channel 5V
Relay Module 16 Channel 5V
231.00 EGPRelay Module 16 Channel 5V
231.00 EGP -
Relay Module 2 Channel 5V (high/low) level trigger
Relay Module 2 Channel 5V is a LOW Level 5V 2-channel relay interface board, and each channel needs a 20mA driver current. It can be used to control various appliances and equipment with large current. It is equipped with high-current relays that work under AC 250 V -10 A or DC 30 V 10 A. It has a standard interface that can be controlled directly by microcontroller
80.00 EGP -
Relay Module 4 Channel – 5V DC
Relay Module 5Vdc – 4 Relay For Arduino & MCU H/L Trigger
150.00 EGPRelay Module 4 Channel – 5V DC
150.00 EGP -
Relay Module 8 Channel 5V
This is a 5V 8-Channels Relay module, It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and MSP430.
8 relays are included in this module, with “NC” ports means “Normally connected to COM” and “NO” ports means “Normally open to COM”. This module also equipped with 8 LEDS to show the status of relays
195.00 EGPRelay Module 8 Channel 5V
195.00 EGP -
Rgb Led Module
- RGB LED is a light emitting diode that displays just about any color by manipulating the intensities of either the Red, the Green or the Blue LED.
10.00 EGPRgb Led Module
10.00 EGP -
SD Card Module, SPI Interface
This is a wonderful little Arduino to SD card interface module.Through programming, you can read and write to the SD card using your arduino.If you are feeling adventurous, this is truly an interesting board to work with and learn from.It is easily interfaced as a peripheral to your arduino sensor shield module.
55.00 EGPSD Card Module, SPI Interface
55.00 EGP -
SILICON POWER USB Flash Ultima U03, 32GB, USB 2.0
Elegant and stylish USB drive with luxurious diamond cut pattern and 32GB storage capacity
110.00 EGP -
-
-
Ublox NEO-6m GPS tested Module
Ublox makes good gps. The Ublox NEO-6M gps engine on this board is a quite good one, with high precision binary output. It has also high sensitivity for indoor applications. The gps module have a battery for power backup and EEprom for storing configuration settings.
The antenna is connected to module through ufl cable which allow for flexibility in mounting the gps such that the antenna will always see the sky for best performance. This make it powerful to use with cars and other mobile applications.
The Ublox gps module has serial TTL output, it has four pins:TX, RX, VCC and GND. You can download the u-center software for configuring the gps and changing the settings and much more. It is really good software (see link below).
600.00 EGPUblox NEO-6m GPS tested Module
600.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories