-
Mini 5V Traffic Light LED Display Module for Arduino Red Yellow Green 5mm LED
Mini 5V Traffic Light LED Display Module for Arduino Red Yellow Green 5mm LED RGB -Traffic Light for Traffic Light System Model
30.00 EGP -
3D Printer Mechanical End Stop Switch Module
3D Printer Mechanical End Stop Switch Module is a Mechanical End stop kit or 3D Printers or CNC machines.
35.00 EGP -
Micro-USB Female Breakout Module
A Female MicroUSB port with breakout board so you can solder on wires or header pins and integrate into any project.
15.00 EGPMicro-USB Female Breakout Module
15.00 EGP -
MAX6675 Module for Thermocouple K Type
This K Type Thermocouple can be used to measure temperatures up to 600 degree Celsius! Great for industrial projects, 3D Printers, DIY and hobby projects which require a high temperature to be measured.
285.00 EGPMAX6675 Module for Thermocouple K Type
285.00 EGP -
XY-LJ02 Timer Relay Delay Switch Module With LCD
XY-LJ02 Timer Relay Delay Switch Module Delay Power Off and Trigger Delay Cycle Timing Circuit Switch with LCD Digital Display Compatible with Arduino
137.50 EGP -
GY-273 3-Axis Compass Magnetometer Sensor Module
GY-273 DC 3V-5V HMC5883L Triple Axis Compass Magnetometer Sensor Module Three Axis Magnetic Field Module for Arduino
210.00 EGP -
SILICON POWER USB Flash Ultima U03, 32GB, USB 2.0
Elegant and stylish USB drive with luxurious diamond cut pattern and 32GB storage capacity
110.00 EGP -
16 Channel Analog Multiplexer
Multiplexer Module is a micro chip that requires 1 Analog Pin and 2 to 4 Digital Pins to allow the micro controller to monitor more Analog Pins for sensor readings. The requirement of 1 Analog Pin is actually the output pin shared among all the extension Analog Pins. The module only allow 1 Analog channel or sensor value to be connected to the output Analog Pin each at a time thus they take turns to operate.
38.50 EGP16 Channel Analog Multiplexer
38.50 EGP -
CH376S U Disk Read Write Module For USB Control Transfer
CH376 is common a USB bus interface chip, with 8 bit data bus and reading, writing and chip select lines and interrupt output, can easily attached to the system bus of the single chip microcomputer /DSP/MCU/MPU controller.
110.00 EGP -
Lipo Battery Voltage Tester / Low Voltage Buzzer Alarm
LIPO Battery Voltage Tester and low voltage buzzer alarm combo is easy to use.
Li-Po Battery Voltage Buzzer+Indicator: directly plug it into your operating battery, it will monitor the conditions of your battery all the time, so your batteries shall remain within safe operating voltage range at all times.
55.00 EGP -
12V Delay Timer Switch Adjustable
This 12V Delay Timer Switch Adjustable 0-10sec is one kind of popular switch module. You can use it control any devices on or off. This is a DC12V controlled 1 channel timer relay module. It has a NE555 timer chip on the board. You can adjust delay time(0-10s) by rotating the potentiometer. When this relay get powered it will delay several seconds before relay turn on.
Note: Recommended power + series with a diode to protect the circuit.
45.00 EGP12V Delay Timer Switch Adjustable
45.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories