Search Results for "motor"
-
TB6560 CNC 3-Axis Driver 3.5A
TB6560 stepper motor driver can drive up to 3 stepper motors with 3.5 A peak current for each motor. It is also equipped with spindle relay output and can handle a spindle. It has micro-stepping capability up to 1/16 micro-step.
The driver is integrated with break output board (so you do not need one) and can be connected directly to the parallel port. In addition, it has a manual control port interface for manual control of your motors.
The 3-axis driver uses Toshiba TB6560AHQ chip and equipped with optical isolation with dc-dc power supply isolation for full protection. Finally, this driver is compatible with most parallel software MACH3, KCAM4 etc.!
825.00 EGPTB6560 CNC 3-Axis Driver 3.5A
825.00 EGP -
2000W SCR Voltage Regulator Dimming Speed Controller Thermostat AC 220V
2000W SCR Voltage Regulator Dimming Speed Controller Thermostat AC 220V
105.00 EGP -
3800W Voltage Regulator, Dimmer, Speed, Temperature Adjustment
3800W Voltage Regulator, Dimmer, Speed, Temperature Adjustment
210.00 EGP -
4000W AC 220V SCR Voltage Regulator Speed Controller Dimmer
4000W 220V AC SCR Voltage Regulator Dimmer Electric Motor Speed Controller Features -With the fuse with the shell, using more secure, installation is more convenient -Use thick 1.6 times high temperature resistant circuit board adopt more upset welding road design, enough to deal with large current -SCR is mainly used for impedance load such as Incandescent light bulbs, electric wire, and most of the single phase AC motor.
500.00 EGP -
-
Mini Water Pump 3-6V DC
This is a low cost, small size Submersible Pump Motor which can be operated from a 2.5 ~ 6V power supply. It can take up to 120 liters per hour with very low current consumption of 220mA. Just connect tube pipe to the motor outlet, submerge it in water and power it. Make sure that the water level is always higher than the motor. Dry run may damage the motor due to heating and it will also produce noise.
80.00 EGPMini Water Pump 3-6V DC
80.00 EGP -
ESP32 Development Board (WIFI and Bluetooth)
ESP32 Development Board (WIFI and Bluetooth)
400.00 EGPESP32 Development Board (WIFI and Bluetooth)
400.00 EGP -
-
FST/CZS 433Mhz Wireless Transmitter Module
Wireless Transmitter Module
This is 433Mhz RF transmitter with receiver kit for Arduino ARM MCU wireless, It’s Uses Remote control switch, receiver module, motorcycles, automobile anti-theft products, home security products, electric doors, shutter doors, windows, remote control socket, remote control LED, remote audio remote control electric doors, garage door remote control, remote control retractable doors, remote volume gate, pan doors, remote control door opener, door closing device control system, remote control curtains, alarm host, alarm, remote control motorcycle remote control electric cars, remote control MP3
45.00 EGP -
A3967 Easy Driver Microstepping Driver
The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver).
95.00 EGPA3967 Easy Driver Microstepping Driver
95.00 EGP -
-
Relay Module 1 Channel 5V
The Single Channel Relay Module is a convenient board that can be used to control high voltage, high current loads such as motor, solenoid valves, lamps, and AC load.
It is designed to interface with microcontrollers such as Arduino, PIC and etc.
The relays terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes with a LED to indicate the status of the relay.
50.00 EGPRelay Module 1 Channel 5V
50.00 EGP