-
AVR ISP 10Pin To ICSP 6Pin Converter V2
AVR ISP 10Pin To ICSP 6Pin Converter V2
The standard 10PIN programmer can be used to interface to 6PIN Interface Converter.
MCU development board can be used to download Interface Converter and also an Arduino development board can be used for the ISP interface converter.
35.00 EGPAVR ISP 10Pin To ICSP 6Pin Converter V2
35.00 EGP -
Infrared Flame Sensor Module – 4 pin
The Flame Sensor Module can detect flames in the 760 – 1100 nanometer wavelength range. Small flames like a lighter flame can be detected at roughly 0.8m. The detection angle is roughly 60 degrees and the sensor is particularly sensitive to the flame spectrum.
An on-board LM393 op-amp is used as a comparator to adjust the sensitivity level. The sensor has a digital and analog output and sensitivity can be adjusted via the blue potentiometer.
This Flame Sensor Module is used to detect fire/flame source or other light sources of the wavelength in the range of 760nm – 1100 nm. It is based on the YG1006 sensor which is a high speed and high sensitive NPN silicon phototransistor. Due to its black epoxy, the sensor is sensitive to infrared radiation.
The sensor can be a great addition in a firefighting robot, it can be used as a robot eyes to find the fire source. When the sensor detects flame the Signal LED will light up and the D0 pin goes LOW.
The module has 2 outputs: Analogue, which gives a real-time voltage output signal on thermal resistance, and digital which allows temperature thresholds to be set via a potentiometer.
Features :
- High Photo Sensitivity
- Fast Response Time
- Sensitivity adjustable
- Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
- Detection range: up to 100 cm.
- Adjustable detection range.
- Detection angle about 60 degrees, it is sensitive to the flame spectrum.
- Comparator chip LM393 makes module readings stable.
- Operating voltage 3.3V-5V.
- Digital and Analog Output.
- Power indicator and digital switch output indicator.
Package Includes :
1 x Flame Sensor Module
35.00 EGPInfrared Flame Sensor Module – 4 pin
35.00 EGP -
16 Channel Analog Multiplexer
Multiplexer Module is a micro chip that requires 1 Analog Pin and 2 to 4 Digital Pins to allow the micro controller to monitor more Analog Pins for sensor readings. The requirement of 1 Analog Pin is actually the output pin shared among all the extension Analog Pins. The module only allow 1 Analog channel or sensor value to be connected to the output Analog Pin each at a time thus they take turns to operate.
38.50 EGP16 Channel Analog Multiplexer
38.50 EGP -
PAM8403 Audio Amplifier With Volume Control
PAM8403 2 Channel USB Power Audio Amplifier Module Board 3Wx2 Volume Control
38.50 EGP -
Joystick Module X-Y For Arduino
Lots of robotic projects need a joystick. This module offers an affordable solution to that. The Joystick module is similar to analog joysticks found in gamepads. It is made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.
40.00 EGPJoystick Module X-Y For Arduino
40.00 EGP -
RS232 to TTL Converter (Max232)
The RS232 To TTL Converter Module is widely used in radio modifications, cell phone Flash, XBOX360 Flash detection, GPS, car, DVD Flash, HDD repair, set-top box upgrade.
40.00 EGPRS232 to TTL Converter (Max232)
40.00 EGP -
USB to UART/ESP8266 Adapter Programmer for ESP-01 WIFI Modules with CH340G Chip
USB to UART/ESP8266 Adapter Programmer for ESP-01 WIFI Modules with CH340G Chip
- Driver Chip: CH340G
- Supports all basic windows versions.
- The adapter plate integrated 1000μF solid capacitors to ensure the current supply
- The power supply will not be a problem to make WIFI module crashes unresponsive.
- Using 3225 SMD crystal oscillator, improve the stability of serial work, on a beautiful and tall.
- Working voltage: 4.5V – 5.5V (Onboard 3.3v LDO Regulator)
- Working current: 300mA (LDO regulator can supply)
40.00 EGP -
DS1307 RTC Module 24C32 Memory
DS1307 RTC Module 24C32 Memory
45.00 EGPDS1307 RTC Module 24C32 Memory
45.00 EGP -
FST/CZS 433Mhz Wireless Transmitter Module
Wireless Transmitter Module
This is 433Mhz RF transmitter with receiver kit for Arduino ARM MCU wireless, It’s Uses Remote control switch, receiver module, motorcycles, automobile anti-theft products, home security products, electric doors, shutter doors, windows, remote control socket, remote control LED, remote audio remote control electric doors, garage door remote control, remote control retractable doors, remote volume gate, pan doors, remote control door opener, door closing device control system, remote control curtains, alarm host, alarm, remote control motorcycle remote control electric cars, remote control MP3
45.00 EGP -
Audio Amplifier Module (LM386-Adjustable Gain)
Audio Amplifier Module (LM386-Adjustable Gain)
45.00 EGP -
DC-DC USB Boost Step-up Converter 0.9V-5V to 5V
DC-DC USB Boost Step-up Converter 0.9V-5V to 5V
45.00 EGP60.00 EGPDC-DC USB Boost Step-up Converter 0.9V-5V to 5V
45.00 EGP60.00 EGP -
12V Battery Level LED Indicator
XD-82B 12V Battery Level Indicator Module 4 Paragraph 4 onboard Battery Indicator LED Lights.
Monitor the level of your 12v battery and know when it’s running low with this small LED battery level indicator.
45.00 EGP12V Battery Level LED Indicator
45.00 EGP
Shop By Department
- Arduino Shields
- Audio and Sound
- Batteries & Accessories
- Cables/Wires
- Classic Control Components
- Components
- Developments Boards
- Integrated Circuits
- Light Source and Display
- Mechanical Parts
- Measuring Devices
- Modules
- Motors
- Power Sources
- Programmers
- Robotics
- Sensors
- Switches
- Tools
- Terminals & Connectors
- Inverters
- Camera
- Mobile Accessories