نظرا لعدم استقرار الأسعار ، نعتذر لكم عن أنه قد يكون هناك بعض الاختلاف في أسعار البيع مؤقتا لحين ضبط الأسعار ,, شكرا لتفهمكم

New Amazing IBT-2 Motor Driver 43A - Electra

IBT-2 Motor Driver 43A

275.00 EGP

Out of stock

IBT-2 43A H-Bridge Motor Driver Module the drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection.
motor driver H-bridge driver circuit, with strong drive and braking effect, use 74HC244 chip effectively isolate the microcontroller and the motor drive High Current up to 43A
IBT-2 motor driver is a fully integrated high current H bridge module for motor drive applications.
Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with current sense, slew rate adjustment, dead time generation and protection against overtemperature, overvoltage, under voltage, overcurrent and short circuit.
provides a cost optimized solution for protected high current PWM motor drives with very low board space consumption.
The 43a motor driver IBT-2 H-bridge module is an inexpensive, high power motor driver based on two BTS7960 chips
This driver 43a motor driver uses two high current half bridge Infineon BTS 7960 chip for motor drive applications. Interfacing to a microcontroller is made easy using this driver which features current sensing, slew rate adjustment and protection against over temperature, overvoltage, under voltage, over current and short circuit.
This small size driver provides a cost optimized solution for protected high current PWM motor drives.

Email when stock available

Compare
IBT-2 43A H-Bridge Motor Driver Module the drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection.

Features: 

  • 5V isolate with MCU, and effectively protect MCU; 5V power indicator on board.
  • Voltage indication of motor driver output end; can solder heat sink.
  • Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2); isolation chip 5 V power supply (can share with MCU 5 V).
  • Able to reverse the motor forward, two PWM input frequency up to 25kHZ; two heat flow passing through an error signal output.
  • Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply; the supply voltage 5.5V to 27V.

 IBT-2 43A H-Bridge Motor Driver Module Specifications: –

  • Input Voltage: 6 ~ 27Vdc.
  • Driver: Dual BTS7960 H Bridge Configuration.
  • Peak current: 43-Amp.
  • PWM capability of up to 25 kHz.
  • Control Input Level: 3.3~5V.
  • Control Mode: PWM or level
  • Working Duty Cycle: 0 ~100%.
  • Over-voltage Lock Out.
  • Under-voltage Shut Down.

IBT-2 43A H-Bridge Motor Driver Module Pin Description: –

  • RPWM: forward level or PWM signal input, active high.
  • LPWM: Reverse level or PWM signal input, active high.
  • R_EN: forward drive enable input, high-level enable, low level off.
  • L_EN: Reverse drive enable input, high-level enable, low level off.
  • R_IS: forward drive current alarm output.
  • L_IS: Reverse drive current alarm output.
  • VCC: +5 V power output, 5V power supply connection with the microcontroller.
  • GND: signal common low end

Package Included:

  • 1 x IBT-2 43A H-Bridge Motor Driver Module

Electra group

Be the first to review “IBT-2 Motor Driver 43A”

Reviews

There are no reviews yet.

WeCreativez WhatsApp Support
Our customer support team is here to answer your questions. Ask us anything!
👋 Hi, how can I help?

Main Menu