Search Results for "arduino"
-
Arduino Mega 2560 Pro Embed CH340G – ATmega2560-16AU Development Board
Embedded version of Mega 2560 CH340G / ATmega2560-compatible with Arduino Mega 2560 board. Built in ATmega2560 Atmel microcontroller and CH340G USB-UART interface chip.
1,400.00 EGP -
3Amp 4V-16V DC Motor Driver MDD3A (2 Channels)
Looking for a motor driver for your mobile robot? Want to drive a stepper motor? Worry not! MDD3A is able to control two brushed DC motors or single bipolar/unipolar stepper motor from 4V to 16V.
With discrete MOSFETs H-Bridge design, this motor driver is able to support 3 Amp per channel continuously without any additional heatsink.
625.00 EGP -
HW-069 4 Digits 7 Segment Display Module with 0.36Inch Time Clock TM1637 Driver
The module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point.The driver chip is TM1637.
It only needs 2 signal lines to enable the MCU to control the 4-bit 8-segment digital tube
45.00 EGP -
Cytron Dual Channel 10A DC Motor Driver Rev 2.0 – MDD10A (10A Each Channel)
This is a dual motor driver which is designed to drive 2 DC motor with high current up to 10A continuously and 30A peak. The driver works in the voltage range from 5 to 25 V. It also includes a fast test switch for driver testing.
This driver supports locked-antiphase and sign-magnitude PWM signal. It uses full solid-state components which result in faster response time and eliminate the wear and tear of the mechanical relay Cytron Dual Channel
1,350.00 EGP -
Dual Monster Moto Shield VNH2SP30 DC Motor Driver 30A
The Dual Monster Moto Shield VNH2SP30 DC Motor Driver 2x14A (Peak 30A) is essentially a ramped up version of our Ardumoto motor driver shield. For this Monster Moto Shield, It is replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers.
264.00 EGP -
3D Print Control Board Ramps v1.4 Shield for Arduino Mega
Ramps is short for reprap Arduino Mega shield, it is mainly designed for the purpose of using stepper driver board (similar to 4988 driver board). Ramps can only work when connected to mainboard Mega 2560 and DRV8825. Great compatibility with most 3Dprinter (all reprap-model such as pursa i2 and i3).
Note: This Board is only the shield, Stepper Drivers and mainboard are not included.
170.00 EGP -
Makey Makey Touch Key Usb Shield
Makey Makey Touch Key Usb Shield
200.00 EGP370.00 EGPMakey Makey Touch Key Usb Shield
200.00 EGP370.00 EGP -
Xbee Zigbee PRO Shield
Xbee Zigbee PRO Shield
90.00 EGP110.00 EGPXbee Zigbee PRO Shield
90.00 EGP110.00 EGP -
Joystick Shield V1 For Arduino
The Joystick Shield V1.A is an Uno compatible shield that allows you to turn an Arduino Uno or compatible into a game console or robotic controller.The joystick Shield V1.A will let you turn your Arduino board into a controller like the game console system. It can be used to control anything from a remote control car to anything that you can think of. It also provides a lot of different interfaces.
110.00 EGPJoystick Shield V1 For Arduino
110.00 EGP -
L293D Arduino Dual Motor Shield
L293 Motor Driver Shield for DC motor/ stepper motor / servo motor
115.00 EGPL293D Arduino Dual Motor Shield
115.00 EGP -
Lcd Touch Module 2.8 Inch Tft Shield For Arduino Uno
Lcd Touch Module
280.00 EGP -
3D Printer Ultimaker V. 1.5.7 Pcb Compatible With Ramps Arduino Mega 2560 R3
The Ultimaker 1.5.7 board is an Arduino Mega shield, geared for the DIY 3D printer market and has some great features not found on the RAMPS compatible boards such as higher input voltage ability and power connectivity options.
Controls up to 5 stepper motors and Compatible with Pololu stepper driver boards 3D Printer Ultimaker
390.00 EGP450.00 EGP3D Printer Ultimaker V. 1.5.7 Pcb Compatible With Ramps Arduino Mega 2560 R3
390.00 EGP450.00 EGP